DCPompe immergée2″

2″ DC Screw Solar Pump

Name: 2″ DC Screw Solar Pump
Brand: Aquasolar

140 mHauteur max.

1.7 m³/hDébit max.

180–750 WPlage de puissance

2 yrGarantie

✓ 2-yr Garantie✓ 70+ pays✓ 15+ ans d'expérience✓ CE · RoHS · ISO

Engineering note. Maximum head and maximum flow are curve endpoints, not one simultaneous duty point. Final selection is verified against your total head, required flow and solar resource.

↓ Fiche technique (PDF)Demander un devis

Permanent-magnet brushless motor + intelligent MPPT (auto start/stop, soft-start)
Controller LED display: voltage / current / power / speed (RPM) / error code
Oil cooling
Full protection: over/under-voltage, overload, over-current, dry-run, reverse, over-temp
Runs directly off PV modules — no batteries required
Progressive-cavity screw + SUS304 sleeve — well-suited to sandy / silty water

Spécifications

#	Model	Tension (V)	Puissance (W)	Courant (A)	Débit max. (m³/h)	Hauteur max. (m)	Refoulement	Ø (mm)	Longueur (mm)	Poids (kg)	Câble recommandé (mm²)	PV recommandé
1	2PWSS1.2-45-24-180	24	180	7.5	1.2	45	0.75"	50	545	4.3	2.5	1 × 250 Wp
2	2PSC1.5-35-24-250	24	250	10.4	1.5	35	0.75"	50	550	4.6	4	1 × 330 Wp
3	2PWSS1.2-60-24-250	24	250	10.4	1.2	60	0.75"	50	550	4.6	4	1 × 330 Wp
4	2PSC1.5-60-48-400	48	400	8.3	1.5	60	0.75"	50	570	5.3	2.5	2 × 300 Wp
5	2PWSS1.5-90-48-400	48	400	8.3	1.5	90	0.75"	50	570	5.3	2.5	2 × 300 Wp
6	2PSC1.5-85-72-600	72	600	8.3	1.5	85	0.75"	50	600	6.2	2.5	3 × 300 Wp
7	2PWSS1.5-120-72-600	72	600	8.3	1.5	120	0.75"	50	600	6.2	2.5	3 × 300 Wp
8	2PWSS1.7-140-96-750	96	750	7.8	1.7	140	0.75"	50	620	6.9	2.5	3 × 300 Wp

Moteur & Entraînement

Moteur	Permanent-magnet DC brushless (PMSM)
Entraînement	Sensorless FOC, pure sine-wave output
Suivi MPPT	>99%
Classe d'isolation	F (155 °C)
Service	S1 (continuous)
Indice IP	IP68 (submersible motor) / IP66
Immersion max.	150 m
Garantie	2

Contrôleur & Protections

Contrôleur	Sensorless FOC sine-wave vector drive + MPPT (>99%), LED display
Affichage	Voltage, Current, Power, Speed (RPM), Speed adjustment, Error code
Taille du contrôleur	250 × 175 × 110 mm

Protections

OverloadOver-currentUnder-loadUnder-voltageReverse-connectionOver-temperature (thermal)Dry-run / low-waterSoft-start

Surveillance à distance (option): Optional 4G/GSM or Wi-Fi monitoring module — remote flow, water level, energy and fault alerts with OTA updates (add-on; the standard controller uses a local LED display).

Conditions de fonctionnement

Température de l'eau	0–40 °C
Teneur en sable	≤ 0.25 % (sand-tolerant screw)
Plage de pH	5–9
Température ambiante	-15 to 70 °C
Forage min.	52 mm

Matériaux

Standard — SUS304 outer sleeve + steel/NBR progressive screw rotor + SUS304 shaft (Progressive-cavity screw handles sandy / silty water well)
Corrosion (option) — SUS316 sleeve, shaft & fittings
Economy (option) — SUS201 sleeve (lower cost, reduced corrosion resistance)

Composants premium

100% copper motor windings
Class F (155 °C) insulation system
NSK-grade sealed ball bearings
SUS304 shaft + steel/NBR progressive-cavity screw (sand-tolerant)
NBR stator — handles silty / sandy water
Oil-cooled motor
PMSM + sensorless FOC sine-wave controller, MPPT >99%

Câble recommandé

PV-to-controller & motor cable 2.5–4 mm² by model (copper, sized for a ~50 m run; step up one size per additional ~50 m of drop).

Per-model cable cross-section is listed in the specification table above (mm² column).

Certifications

RoHSCBTUVSGSISO 9001ISO 14001

Normes

IEC 62253 (PV pumping systems)IEC 60034 (rotating machines)IEC 60529 (enclosure / IP)

Pompe immergée

DCPompe immergée